Plainsheet

Guide · updated 2026-11-16

How to classify a mixture under GHS and CLP

When you blend raw materials into a product, the product needs its own hazard classification. You rarely have test data for the finished product. So the rules let you calculate the classification from the classified ingredients. This guide covers the calculation method used for most small-maker products. It follows Annex I of the EU CLP Regulation (EC) No 1272/2008, and the GHS text it is based on.

The figures below are the generic limits. If an ingredient's SDS gives a specific concentration limit (SCL) or an M-factor, use that value instead. It overrides the generic limit for that ingredient.

Step 1: list the relevant ingredients

Take every ingredient and its percentage by weight. A bought-in mixture, such as a fragrance oil, is best broken down into the substances in section 3 of its SDS. Multiply each component's percentage by the dose you use. For example, linalool at 10% in a fragrance used at 8% gives 0.8% in the candle. Where the SDS gives a range, the cautious choice is the upper value.

Ingredients below the generic cut-off for a hazard class are not counted for that class:

Hazard classGeneric cut-off
Acute toxicity, Categories 1–30.1%
Acute toxicity, Category 41%
Skin corrosion and irritation, eye damage and irritation1%
Aquatic Acute 1 and Aquatic Chronic 10.1% (divided by the M-factor)
Aquatic Chronic 2, 3 and 41%

Step 2: hazards that are not added up

Some hazards apply when a single ingredient reaches a limit. Two sensitisers at 0.6% each do not make a sensitising mixture. One sensitiser at 1% does.

Ingredient classificationMixture is classified if one ingredient is at or above
Skin Sens. 1 or 1B (H317)1% (EUH208 "may produce an allergic reaction" from 0.1%)
Skin Sens. 1A (H317)0.1% (EUH208 from 0.01%)
Resp. Sens. 1 or 1B (H334)1% for liquids and solids
Muta. 1A/1B (H340), Carc. 1A/1B (H350)0.1%
Muta. 2 (H341), Carc. 2 (H351)1%
Repr. 1A/1B (H360)0.3%
Repr. 2 (H361)3%
Lactation (H362)0.3%
STOT SE 1 or STOT RE 1 (H370, H372)10% gives Category 1. From 1% to under 10% gives Category 2.
STOT SE 2 or STOT RE 2 (H371, H373)10%

Step 3: hazards that are added up (summation)

Skin corrosion and irritation

Serious eye damage and eye irritation

Under EU CLP, skin irritants (H315) are not added into the eye calculation. A product classified H314 also counts as Eye Dam. 1, but the label shows only H314.

STOT SE 3 (H335 and H336)

The mixture takes the category when the ingredients with the same effect add up to 20% or more. Respiratory irritation (H335) and drowsiness (H336) are added up separately.

Aquatic hazards

Each Category 1 ingredient is multiplied by its M-factor (1 unless the SDS says otherwise).

Under GHS (and so in the US, Canada and Australia), there are also Aquatic Acute 2 and 3. OSHA does not regulate environmental hazards, so they appear in section 12 of a US SDS but not on the workplace label.

Step 4: acute toxicity with the ATE formula

Each acutely toxic ingredient has an acute toxicity estimate (ATE). Use its measured LD50 or LC50 if the supplier gives one. Otherwise use the conversion value for its category:

CategoryOral (mg/kg)Dermal (mg/kg)Inhalation, vapours (mg/l)
10.550.05
25500.5
31003003
4500110011

Then 100 ÷ ATE(mix) = Σ (Ci ÷ ATEi). Compare the result with the category limits. For oral toxicity these are ≤ 5, ≤ 50, ≤ 300 and ≤ 2000 mg/kg.

Example. A cleaner holds 20% of an ingredient classified Acute Tox. 4 (oral), with an ATE of 500. 100 ÷ ATE(mix) = 20 ÷ 500 = 0.04, so ATE(mix) = 2500 mg/kg. That is above 2000, so the cleaner is not classified for acute oral toxicity. At 45%, ATE(mix) = 1111 mg/kg, which gives Acute Tox. 4, H302.

If more than 10% of the mixture is made of ingredients with unknown acute toxicity, CLP adds a correction to the formula. Check this case by hand.

Step 5: physical hazards come from measurements

Flammability is not calculated from ingredients. A liquid is classified from its measured closed-cup flash point and initial boiling point:

Worked example: a fragrance at 10% in a candle

The fragrance's SDS lists 10% linalool (Skin Sens. 1B), 15% benzyl salicylate (Skin Sens. 1B, Aquatic Chronic 3), 5% d-limonene (Skin Sens. 1B, Aquatic Acute 1, Chronic 3) and 2% coumarin (Skin Sens. 1B). At a 10% load, the candle contains:

SubstanceIn the candleEffect
Benzyl salicylate1.5%Over the 1% sensitiser limit, so the candle is classified H317
Linalool1.0%Exactly at the limit, so it is also named on the label
d-Limonene0.5%Below 1% but at least 0.1%, so it is named in EUH208
Coumarin0.2%Named in EUH208

For the aquatic hazard, the Chronic 3 total is 1.5%, far below 25%, so there is no aquatic classification. Limonene's acute value of 0.5 × 1 is also far below 25%. The label shows GHS07, the word "Warning", H317, "Contains benzyl salicylate, linalool" and the EUH208 line.

Do this calculation for your own recipe, with the reasoning shown line by line.
Open the calculator

Sources